Auto Glass Tools - Equalizer®

1-1/2" UltraWiz® Cold Knife Blades • 10

IP PN1004

$40.00

PN1004 has a cutting area that is 1-1/2" long. We do not recommend using this blade for initial cuts. Use a shorter blade to make your first cut, then go back with this blade to make your final cut. Especially useful where urethane is very wide, such as corners and along the bottom.

Original Thickness.

Package of ten.

1-1/2" UltraWiz® Cold Knife UltraThin Blades • 10

IP PN5004

$50.00

PN5004 is a 1-1/2" blade and should never be used for the first cut. Always use a shorter blade to make the first cut then finish cutting through the urethane with this long blade.

Package of ten.

BTB Powered Cold Knife Blade • 1-1/4" (30 mm) Narrow Angle • Right Facing Tip

IP WK30AL

$33.00

BTB Powered Cold Knife Blade • 1-1/4" (30 mm) • Right Facing Tip

Narrow-Angle that allows the tool to operate where vehicle body restricts access.

Equalizer™ Grey Textured LED Hat

IP TLH20

$30.00

Equalizer™ LED hat features Ultra Bright LED technology provides you with a perfect hands-free flashlight. 4 LEDs are concealed under the brim with dual beams for long on widespread light coverage.

Neoprene Foam Installation Tape • 1/4" x 1/4" x 18' • 12 pack

IP OSA6494

$73.00

Commonly called foam dams.

On many vehicles you can see the urethane from the inside of the vehicle and this is why manufacturers use a foam dam. Foam dams do two critical things, first they prevent the urethane from squeezing into the vehicle, but secondly and perhaps as equally important is they give a smooth nice looking finish to the inside of a vehicle. While this appearance may not be important to the construction worker driving a work truck, it is very important to a person driving a nice new vehicle. For this reason you should always have a nice selection of these foam dams with you. It is a small price to pay when you consider the alternative of removing a windshield to clean up a messy urethane job.

Adhesive on one side.

#1 Phillips Bit

IP EPB762

$1.00

Replacement #1 Phillips insert bit.

#2 Phillips Bit

IP EPB763

$1.00

Replacement #2 Phillips insert bit.

#3 Phillips Bit

IP EPB764

$1.00

Replacement #3 Phillips insert bit.

$25 Equalizer Visa Gift Card

IP Gift Card

$27.50

$25 Equalizer Visa Gift Card.

1" Gold Glass Group 75' Spool

IP T108B

$74.00

In the past, you could spend more time saving the molding than you spent removing and replacing the windshield. There were many reasons for saving a molding, but the most common reason was that it was difficult to stock all the different moldings. Insurance companies realize that you cannot always save the molding when replacing a windshield. For this reason, they now pay for a new molding when the old one cannot be saved. old Glass Group has solved the first problem. You no longer need to stock dozens of different moldings. You can now reduce your inventory with universal moldings. Four moldings equal over four hundred applications. old Glass Group moldings do not shrink or discolor over time, never crimp around corners, always lay flush against the vehicle, never need a heat gun to install, and fit both thick windshields and thin tempered parts. A thin layer of butyl is made into the channel of each molding. When the molding is pushed onto the glass the butyl adheres to the edge of the glass and the molding will not come off. You will not find T110 listed on the chart at right. They are both intended to replace push-in “Christmas Tree” moldings. The great thing about these moldings is there is adhesive under the part that goes against the vehicle. This adhesive sticks to the vehicle and holds the molding in place while the urethane cures. The adhesive assures a perfect bond and the cured urethane holds it permanently in place.

1" UltraWiz® Cold Knife Blades • 10

IP PN1002

$28.00

PN1002 has a 1" long cutting area. This is the most popular blade because on most vehicles it will cut the urethane with one cut.

Original Thickness.

1" UltraWiz® Cold Knife UltraThin Blades • 10

IP PN5002

$37.00

PN5002 is a 1" UltraThin cold knife blade and the most common size used by technicians.

They are 40% thinner than the regular UltraWiz® blades.

Package of ten.

1" UltraWiz® UltraThin Stainless Steel Cold Knife Blades • 10

IP 7002M

$48.00

These innovative blades have the longest lasting edge available today. Specialized grinding and heat-treating techniques are applied to the production of these high-quality blades to ensure that they maintain a tough edge without becoming brittle. Their design was taken from the original UltraWiz® blades.

Made in the USA.

1" Z Coined Cold Knife Blades • 5

IP Z5

$17.00

These innovative blades will remain flexible and retain their sharpness much longer than the average cold knife blade. The grinding of the blade is at a greater angle than other cold knife blades. This makes the resistance less when pulling the cold knife to cut the urethane. The end result is a cold knife blade that has the ability to resist breaking, last longer and keep a sharp edge. Equalizer produces two types of cold knife blades. Both the standard and the coined blades use the same proprietary hardening process.

The Coined Z Blade... The cutting surface of a coined cold knife blade has the cutting surface of the blade made thinner, only about 35 thousandths of an inch thick. A normal cold knife blade is 62 thousandths thick. Many technicians routinely grind cold knife blades thinner so they will cut easier. Sometimes this grinding will overheat a blade and damage the hardening. Coined Z blades are thinned before they are hardened so there is no need to grind them thinner.

Should I buy coined or not coined blades?

If you use a cold knife blade right out of the box and never grind it thinner, then use the standard thickness Z1, Z2, Z3, or Z7. If you like to take a new blade and grind it thinner before you use it, then you should purchase the "pre-thinned" Z4, Z5, Z6 or Z8.

Made in the USA.

1" Z Cold Knife Blades • 5

IP Z2

$12.00

These innovative blades will remain flexible and retain their sharpness much longer than the average cold knife blade. The grinding of the blade is at a greater angle than other cold knife blades. This makes the resistance less when pulling the cold knife to cut the urethane. The end result is a cold knife blade that has the ability to resist breaking, last longer and keep a sharp edge. Equalizer produces two types of cold knife blades. Both the standard and the coined blades use the same proprietary hardening process.

The Coined Z Blade... The cutting surface of a coined cold knife blade has the cutting surface of the blade made thinner, only about 35 thousandths of an inch thick. A normal cold knife blade is 62 thousandths thick. Many technicians routinely grind cold knife blades thinner so they will cut easier. Sometimes this grinding will overheat a blade and damage the hardening. Coined Z blades are thinned before they are hardened so there is no need to grind them thinner.

Should I buy coined or not coined blades?

If you use a cold knife blade right out of the box and never grind it thinner, then use the standard thickness Z1, Z2, Z3, or Z7. If you like to take a new blade and grind it thinner before you use it, then you should purchase the "pre-thinned" Z4, Z5, Z6 or Z8.

Made in the USA.