Auto Glass Tools - Equalizer®

T-Handle 1/8" Hex Wrench

IP I3108

$5.04

These handy T-handle hex wrenches are included with all of our Equalizer® tools including the Excalibur®. Many people have asked us if they can purchase them as a separate item.

Express® Blade Sharpener

IP SFE329

$19.00

Retain the chisel edge on your Express® Blades!

To get the best performance, it is important to put a good edge on the blade every time you use your auto glass cut-out knife. Since you do not always have access to a bench grinder, this sharpener will do that quick touch up that brings the blade back to a razor-sharp edge. You can sharpen the blade in about 10 seconds by dragging the sharpener across the blade 3 or 4 times. All off-the-shelf sharpeners will put a V-type edge on the blade and this type of sharpening can prevent the tool from working properly. Our Express® Blade Sharpener puts the chisel-type edge on the blade and keeps your auto glass cut-out knife operating at peak performance. It also features a built-in protector to keep you from cutting your hand on the blade.

Super Lube® Sheath Lubricant

IP SLL347

$10.00

This is a high-heat grease made for lubricating the inside of the sheath where contact with the blade sometimes can occur. This contact usually happens when a blade must curve in order to ride against the glass. This curving of the blade pushes it against the sheath and causes wear on both the blade and sheath if no lubricant is used. Using a small amount of our Super Lube® Sheath Lubricant on the inside of the sheath will extend the life of your sheath. This clear, non-toxic formula protects in temperatures ranging from -45°F to + 450°F and its effectiveness will not be reduced by cutting lubricant or water. 3 Oz.

Equalizer® Cutting Lubricant

IP ECL784

$10.00

Using our lubricant improves cutting action and reduces drag on the blade. It will not damage the dash or headliner. Mix at a 16 to 1 ratio (16 parts water to 1 part cutting lubricant) to make 128 ounces of cutting lubricant. The ECL784 contains no dyes, fragrances or VOC’s so that means when you spray the product in a hot car, it won’t take your breath away! Also, it evaporates slower providing a longer lubricating period.

Made in the USA.

8 Oz Bottle.

Course Diamond File

IP LTB275

$11.00

Our Diamond Files are made of monocrystalline diamonds and their strong, single-crystal structure does not break apart with use. If you want to use a lubricant, use only water. To clean them just scrub with a bristle brush and dishwashing soap. The red file is fine and will put a razor edge on your cutting tools. The blue file is coarse and will sharpen blades like a normal file. Total length is 7" long and the file area measures 2-1/2" long which takes up very little room in your toolbox.

Fine Diamond File

IP LTR274

$11.00

Our Diamond Files are made of monocrystalline diamonds and their strong, single-crystal structure does not break apart with use. If you want to use a lubricant, use only water. To clean them just scrub with a bristle brush and dishwashing soap. The red file is fine and will put a razor edge on your cutting tools. The blue file is coarse and will sharpen blades like a normal file. Total length is 7" long and the file area measures 2-1/2" long which takes up very little room in your toolbox.

Express® Sheath

IP ES1406

$30.00

The sheath is a unique idea that allows the Equalizer® auto glass cut-out knives to use a flexible blade and still have the strength to cut the toughest urethane. Equalizer® Express® Blades come in longer and shorter sizes, but there is only one size sheath and it fits all Equalizer® tools that utilize the Express® Blades.

Made in the USA.

Express® Blade • 3" X 14"

IP RLE1404

$42.00

Equalizer® Express® Blades are developed for use on hundreds of different vehicles.

The RLE1404 work well where the urethane is very deep below the dash.

This blade can also be used with our Express® Blade Handle or PushKnife.

Made of a proprietary grade of stainless steel.

Made in the USA.

Express® Blade • 1.5" X 12"

IP LBE1403

$42.00

Equalizer® Express® Blades are developed for use on hundreds of different vehicles.

The LBE1403 blade is perfect for removing glass that is not broken. Its narrow width is more flexible, which puts less stress on the glass.

This blade can also be used with our Express® Blade Handle or PushKnife.

Made of a proprietary grade of stainless steel.

Made in the USA.

Express® Blade • 1.5" X 10"

IP BFE1401

$42.00

Equalizer® Express® Blades are developed for use on hundreds of different vehicles.

The BFE1401 is the most widely used size and is perfect for slicing through wide bands of urethane. It works well in all areas where plunge cut or angle cut are used.

This blade can also be used with our Express® Blade Handle or PushKnife.

Made of a proprietary grade of stainless steel.

Made in the USA.

Express® Blade • 3" X 10"

IP BFE1400

$42.00

Equalizer® Express® Blades are developed for use on hundreds of different vehicles.

The BFE1400 is the most used size and is perfect for slicing through wide bands of urethane.  It works well in all plcaes where you need to plunge cut or angle cut.

This blade can also be used with our Express® Blade Handle or PushKnife.

Made of a proprietary grade of stainless steel.

Made in the USA.

Express® Blade • 3" X 12"

IP LBE1402

$42.00

Equalizer® Express® Blades are developed for use on hundreds of different vehicles.

The LBE1402 work well where the urethane is far below the glass, but there is a limited amount of vertical space inside the vehicle.

This blade can also be used with our Express® Blade Handle or PushKnife.

Made of a proprietary grade of stainless steel.

Made in the USA.

Standard Hydroblade™ • 3" X 12"

IP EHL187

$42.00

Equalizer® HydroBlades™ are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane.

The cutting lubricant allows for each additional stroke of the blade to slide easily through the urethane

The blades are made of stainless steel and have a series of small dimples stamped on the side of the blade that rides against the urethane. Besides making the blade cut easier they also save battery life and reduce vibration because of the reduced friction on the blade.

Made of a proprietary grade of stainless steel.

Made in the USA.

Standard Hydroblade™ • 3" X 10"

IP EHB186

$42.00

Equalizer® HydroBlades™ are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke, the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane.

The cutting lubricant allows for each additional stroke of the blade to slide easily through the urethane. The blades are made of stainless steel and have a series of small dimples stamped on the side of the blade that rides against the urethane. Besides making the blade cut easier they also save battery life and reduce vibration because of the reduced friction on the blade.

Made of a proprietary grade of stainless steel.

Made in the USA.

Standard HydroBlade™ • 1-1/2" x 12"

IP EHL146

$42.00

Equalizer® HydroBlades™ have a series of small dimples stamped on the side of the blade that rides against the urethane. These dimples are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke, the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane allowing for each additional stroke of the blade to slide easily through the urethane. Besides making the blade cut easier they also save battery life and reduce vibration because of the reduced friction on the blade.

Made of a proprietary grade of stainless steel.

Made in the USA.

Standard HydroBlade™ • 1-1/2" x 10"

IP EHB145

$42.00

Equalizer® HydroBlades™ have a series of small dimples stamped on the side of the blade that rides against the urethane. These dimples are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke, the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane allowing for each additional stroke of the blade to slide easily through the urethane. Besides making the blade cut easier they also save battery life and reduce vibration because of the reduced friction on the blade.

Made of a proprietary grade of stainless steel.

Made in the USA.

Standard HydroBlade™ - 3" x 14"

IP EHE160

$42.00

Equalizer® HydroBlades™ have a series of small dimples stamped on the side of the blade that rides against the urethane. These dimples are designed to carry cutting lubricant into the urethane that is being cut by the blade. With each stroke, the blade picks up cutting lubricant on the outside of the urethane and deposits it inside the urethane allowing for each additional stroke of the blade to slide easily through the urethane. Besides, make the blade cut easier they also save battery life and reduce vibration because of the reduced friction on the blade.

Made of a proprietary grade of stainless steel.

Made in the USA.

Spacer HydroBlade™

IP EHS174

$48.00

Some vehicles have a molding with a piece of metal inside. Moldings with metal inserts can be difficult to cut, but by using the Spacer HydroBlade™ cutting these is a breeze. Also, many encapsulated glasses have a very dense encapsulation material that is difficult to cut. To save unbroken glass these blades are designed to hold the blade below the molding and prevent the blade from cutting into the encapsulation. A permanently attached, self-lubricating nylon spacer lets the blade move easily back and forth while holding the blade under the lower lip of the molding or encapsulation.

Made of a proprietary grade of stainless steel.

Made in the USA.

Spacer HydroBlade™

IP EHS175

$48.00

Some vehicles have a molding with a piece of metal inside. Moldings with metal inserts can be difficult to cut, but by using the Equalizer™Spacer HydroBlade™ cutting these is a breeze. Also, many encapsulated glasses have a very dense encapsulation material that is difficult to cut. To save unbroken glass these blades are designed to hold the blade below the molding and prevent the blade from cutting into the encapsulation. A permanently attached, self-lubricating nylon spacer lets the blade move easily back and forth while holding the blade under the lower lip of the molding or encapsulation.

Made of a proprietary grade of stainless steel.

Made in the USA.

Piranha™ Blade • 3"W x 10"L

IP PHB169

$48.00

The Equalizer^® Piranha^™ blade uses the same cutting technology as the original HydroBlade^™ but also incorporates serration on a portion of each side of the blade, making a cutting action from left to right and right to left much easier.

Piranha™ Blade • 3"W x 12"L

IP PHB174

$48.00

The Equalizer^® Piranha^™ blade uses the same cutting technology as the original HydroBlade^™ but incorporates serration on portions of each side of the blade, making the cutting action from side to side much easier.

Piranha™ Blade • 3"W x 14"L

IP PHB175

$53.00

The Equalizer^® Piranha^™ blade uses the same cutting technology as the original HydroBlade^™ but also incorporates serration on a portion of each side of the blade, making a cutting action from left to right and right to left much easier.

Quarter Glass & Corner HydroBlade™ • Passenger Side

IP HQS176

$42.00

Many quarter glasses come to a sharp point in the back and can be difficult to remove. These blades are designed to reach into those difficult areas and cut the urethane with a serration for an even better cut!. They are also very useful for those vehicles that have corners with sharp angles. It can be very challenging to reach into some of those corners to cut the urethane. The blades are very flexible to allow the tool to be held outside the quarter glass opening while cutting inside. Each blade is designed for a specific side of the vehicle.

Made of a proprietary grade of stainless steel.

Made in the USA.

Equalizer® Quarter Glass & Corner HydroBlade™ • Passenger Side

Quarter Glass & Corner HydroBlade™ • Driver Side

IP HQS177

$42.00

Many quarter glasses come to a sharp point in the back and can be difficult to remove. These blades are designed to reach into those difficult areas and cut the urethane with a serration for an even better cut!. They are also very useful for those vehicles that have corners with sharp angles. It can be very challenging to reach into some of those corners to cut the urethane. The blades are very flexible to allow the tool to be held outside the quarter glass opening while cutting inside. Each blade is designed for a specific side of the vehicle.

Made of a proprietary grade of stainless steel.

Made in the USA.

Equalizer® Quarter Glass & Corner HydroBlade™ • Driver Side

1-3/8" Wide, 12" Long • Driver Side

Wide Quarter Glass & Corner HydroBlade™ • Passenger Side

IP HQW178

$42.00

Now Serrated For An Even Better Cut!

These blades are the same as our HQS176 and HQS177 but are wider to accommodate the quarter glasses and corners that are not as pointed. The blades are very flexible to allow the tool to be held outside the quarter glass opening while cutting inside. Each blade is designed for a specific side of the vehicle. Made of a proprietary grade of stainless steel.

Made in the USA.

Equalizer® 2" Wide, 12" Long • Passenger Side

Wide Quarter Glass & Corner HydroBlade™ • Driver Side

IP HQW179

$42.00

Now Serrated For An Even Better Cut!

These blades are the same as our HQS176 and HQS177 but are wider to accommodate the quarter glasses and corners that are not as pointed. The blades are very flexible to allow the tool to be held outside the quarter glass opening while cutting inside. Each blade is designed for a specific side of the vehicle. Made of a proprietary grade of stainless steel.

Made in the USA.

Express™ Blade Handle

IP MEH234

$19.00

A lightweight aluminum handle for Equalizer® Express™ Blades.  

Invented by: George Lytton

12" Standard Blades • 5

IP EEB797PKG

$43.00

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 4" &  8" sizes.

Invented by: Ray Asbery

Made of Spring Steel in the USA.

4" Standard Blades • 5

IP EEB793PKG

$33.00

8" Standard Blades • 5

IP EEB795PKG

$38.00

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 4" and 12" sizes.

Invented by: Ray Asbery

Made of Spring Steel