Auto Glass Tools - Equalizer®

Fine Diamond File

IP LTR274

$11.00

Our Diamond Files are made of monocrystalline diamonds and their strong, single-crystal structure does not break apart with use. If you want to use a lubricant, use only water. To clean them just scrub with a bristle brush and dishwashing soap. The red file is fine and will put a razor edge on your cutting tools. The blue file is coarse and will sharpen blades like a normal file. Total length is 7" long and the file area measures 2-1/2" long which takes up very little room in your toolbox.

BTB Depth Control Arm

IP WK11AW

$11.00

This depth control arm has a thin 1/32" wheel and is intended to be used over the Yellow
WK3, WK4, & “Z” blades. The wheel rolls smoothly along uneven (in & out) urethane surfaces.
WK11AW

BTB Depth Control Arm

IP WK11EW

$11.00

This is a long depth control arm with a thin 1/32" wheel designed to roll smoothly along uneven
(in & out) urethane surfaces. It is intended for use over WK1 & WK1S long blades for excellent
control on blade-cutting depth where a long reach below deep dashboards is necessary.
WK11EW

12" Serrated Blade

IP ESB1312

$12.00

Invented by: Ray Asbery

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 4" and 8" sizes.

Made in of spring steel in the USA.

BTB Manual Handle

IP WK7

$12.00

 For Blades & Pinchweld Preparation Tools

BTB Depth Control Arm

IP WK11BW5

$13.00

This depth control arm has a large plastic wheel that rolls along the A-pillar trim, soft
headliner or vehicle body panel. It is intended to be used over the Yellow WK3, WK4,
& “Z” blades.
WK11BW5

BTB Depth Control Arm

IP WK11DW5

$13.00

This depth control arm is made with a large plastic wheel and intended for use under blades WK5 & WK5S when removing backfill from the glass edge (buses & trains). In this application, the wheel rolls along the glass. It is also used over other flat blades such as WK2S to control cutting depth for longer reach cutting applications. When used in this application the wheel rolls along the window glass or vehicle body trim.

BTB Depth Control Arm

IP WK11CW

$15.00

This depth control arm with a 1/32" wide wheel on each end spaces the blade away from
the encapsulated glass and is designed to roll smoothly along uneven (in & out) urethane
surfaces. The arm provides support for the Orange reverse blades to avoid any blade flapping
or shaking. Use the long offset end under the Orange WK4RS blade. Use the short end under
the Orange WK4ZRS & WK24ZRS blades.
WK11CW

BTB Depth Control Arm

IP WK11FW

$15.00

This depth control arm has a thin 1/32" wheel on each end designed to roll smoothly along uneven (in & out) urethane surfaces
and encapsulated moulding. Use the long offset end over the Yellow WK2, WK2S, WK24 & WK24S blades or under the Orange
WK24RS blade for encapsulated glass removal. Use the short offset end over Yellow WK3 & WK4 blades or under the Orange
WK4RS blade for encapsulated glass removal.
WK11FW

BTB Pinchweld Preparation Blade • 1-9/16"

IP WK640

$16.00

Use for pinchweld preparation. This is a wide blade that works great for Urethane, Body Deadener, and Seam Sealer Removal.

1-9/16" Wide.

Express™ Blade Handle

IP MEH234

$19.00

A lightweight aluminum handle for Equalizer® Express™ Blades.  

Invented by: George Lytton

Express® Blade Sharpener

IP SFE329

$19.00

Retain the chisel edge on your Express® Blades!

To get the best performance, it is important to put a good edge on the blade every time you use your auto glass cut-out knife. Since you do not always have access to a bench grinder, this sharpener will do that quick touch up that brings the blade back to a razor-sharp edge. You can sharpen the blade in about 10 seconds by dragging the sharpener across the blade 3 or 4 times. All off-the-shelf sharpeners will put a V-type edge on the blade and this type of sharpening can prevent the tool from working properly. Our Express® Blade Sharpener puts the chisel-type edge on the blade and keeps your auto glass cut-out knife operating at peak performance. It also features a built-in protector to keep you from cutting your hand on the blade.

BTB "Winged" Anti-Scratch Pinchweld Preparation Blade • 1" Wide

IP WK6L

$19.00

These blades are sharpened on the outside of the curve and help to avoid damage to paint when removing excess urethane after a windshield removal or removing urethane with shattered tempered glass fragments.

BTB "Winged" Anti-Scratch Pinchweld Preparation Blade • 3/4" Wide

IP WK6M

$19.00

These blades are sharpened on the outside of the curve and help to avoid damage to paint when removing excess urethane after a windshield removal or removing urethane with shattered tempered glass fragments.

BTB "Winged" Anti-Scratch Pinchweld Preparation Blade • 1/2" Wide

IP WK6S

$19.00

These blades are sharpened on the outside of the curve and help to avoid damage to paint when removing excess urethane after a windshield removal or removing urethane with shattered tempered glass fragments.