Auto Glass Tools - Equalizer®

Talon™ Oscillating Powered Cold Knife Blade • 1"

IP 51848

$11.00

Our standard sharpened blades are made of hardened carbon steel and are bent the same way regular cold knife blades are. They cut urethane either by thrusting forward into the urethane or backward into the urethane as you move the oscillating tool.

These blades will fit the Falcon, Raven, and TimeSaver tools as well as most oscillating tools in the market.

Will not fit the Ninja™ line of tools.

Talon™ Oscillating Powered Cold Knife Blades • 1-1/2"

IP 51849

$11.00

Our standard sharpened blades are made of hardened carbon steel and are bent the same way regular cold knife blades are. They cut urethane either by thrusting forward into the urethane or backward into the urethane as you move the oscillating tool.

These blades will fit the Falcon, Raven, and TimeSaver tools as well as most oscillating tools in the market.

Will not fit the Ninja™ line of tools.

Ninja Blade • 1-1/2"

IP ENL842

$11.00

Ninja™ Blades are designed especially for Ninja™ and withstand the power produced by the oscillating motion of the air tool. The reverse sharpened blade is perfect for cutting close to the pinchweld while cutting urethane on difficult to remove back glasses.

Made of hardened spring steel.

Course Diamond File

IP LTB275

$11.00

Our Diamond Files are made of monocrystalline diamonds and their strong, single-crystal structure does not break apart with use. If you want to use a lubricant, use only water. To clean them just scrub with a bristle brush and dishwashing soap. The red file is fine and will put a razor edge on your cutting tools. The blue file is coarse and will sharpen blades like a normal file. Total length is 7" long and the file area measures 2-1/2" long which takes up very little room in your toolbox.

Fine Diamond File

IP LTR274

$11.00

Our Diamond Files are made of monocrystalline diamonds and their strong, single-crystal structure does not break apart with use. If you want to use a lubricant, use only water. To clean them just scrub with a bristle brush and dishwashing soap. The red file is fine and will put a razor edge on your cutting tools. The blue file is coarse and will sharpen blades like a normal file. Total length is 7" long and the file area measures 2-1/2" long which takes up very little room in your toolbox.

UltraWiz® Pull Handle

IP PN3010RK

$11.00

Pull handle for PN3001K, 3007K, BNQ271, and BQS257 cold knives.

Squire™ Wire • 72'

IP SSW508

$11.00

When the Squire™ wire is pulled, the pressure is put on the flat side of the wire but as pressure increase, while cutting, Squire™ takes the path of least resistance, twisting and cutting with the edges of the wire. 

The flat side of Squire™ is .25 mm and the diagonal measure is approximately .35 mm.

The roll measures 72' (22M) long. 

Triad™ Wire • 72' (22M)

IP TRI78

$11.00

Triad™ triangular wire is designed to our specifications for cutting urethane.

Made of high-tensile strength stainless steel. Each side of the wire measures .85 mm. Rolls measure 72' (22m).

Reverse Ground Ninja™ Blade • 1-1/2"

IP URL888

$11.00

These blades are the same as the ENT840, ENO841, and ENL842, but they are ground in a reverse direction. This design is perfect for cutting out those difficult to remove back glasses or anytime you want to cut close to the pinchweld.

Reverse Ground Ninja™ Blade • 3/4"

IP URS886

$11.00

Ninja™ blades are made especially for the Ninja™ tool and designed to withstand the power produced by the back and forth motion of the air tool. The Reverse Sharpened blades are perfect for cutting out those difficult to remove back glasses or anytime you want to cut close to the pinchweld.

All are made of hardened spring steel.

BTB Depth Control Arm

IP WK11AW

$11.00

This depth control arm has a thin 1/32" wheel and is intended to be used over the Yellow
WK3, WK4, & “Z” blades. The wheel rolls smoothly along uneven (in & out) urethane surfaces.
WK11AW

BTB Depth Control Arm

IP WK11EW

$11.00

This is a long depth control arm with a thin 1/32" wheel designed to roll smoothly along uneven
(in & out) urethane surfaces. It is intended for use over WK1 & WK1S long blades for excellent
control on blade-cutting depth where a long reach below deep dashboards is necessary.
WK11EW

Wire Loops

IP WL1135

$11.00

Replacement wire loops for the LS1134 Wire Starter.

Package of five.

Reverse Ground Powered Cold Knife Blade • 1"

IP 51842

$12.00

These blades are the same as the 51847, 51848, and 51849 but with one very important difference; they are ground in the reverse direction from a regular cold knife blade. Some, very difficult to remove, back glasses can be cut out with a powered cold knife blade, but it must be sharpened in this reverse direction. Perfect for any time you want to cut close to the pinchweld.

These blades will fit the Falcon, Raven, and TimeSaver tools as well as most oscillating tools in the market.

Will not fit the Ninja™ line of tools.

12" Serrated Blade

IP ESB1312

$12.00

Invented by: Ray Asbery

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 4" and 8" sizes.

Made in of spring steel in the USA.