Auto Glass Tools - Equalizer®

Blade Retaining Washer

IP 2605

$3.96

A blade retaining washer for Equalizer Ninja GT EGT149/EGK150,  Falcon ESM519/ESK520, and TimeSaver ETS6602.

Please refer to schematic breakdown for part identification.

Ricochet™ Pinchweld Protector • 18"

IP PEL815

$4.00

Replacement 18" Pinchweld Protector for Equalizer® Ricochet™ Pinchweld Protection System (PHV859).

Ricochet™ Pinchweld Protector • 24"

IP PTF816

$5.00

Replacement 24" Pinchweld Protector for Equalizer® Ricochet™ Pinchweld Protection System (PHV859).

BTB Guide For Saw Blades

IP SPB345

$5.00

This is the guide that controls the saw blade.

TightWire™ • 72'

IP TW72

$5.00

Composed of three super-strong stainless steel wires, braided to form a cable. When it is pulled the braided material cuts with a sawing action.

TightWire™ diameter measure .22 mm and measure 72' (22m) long. 

BTB Tool Oil

IP WK10OB

$5.00

BTB Tool Oil
Why will a BTB tool run on 4 CFM and produce the power of a much larger tool? The close tolerances of the tool is
the answer. Because of the close tolerances, regular air tool oil can gum up the motor. For this reason we strongly
recommend using only BTB air tool oil.
WK10OB • 1 Fluid Oz.

Self Adhesive Velcro® Pads

IP WK11VEL

$5.00

Self-Adhesive Velcro® Pads attach to the blades so they will glide easily on the glass without causing any damage.

Roll of 25

Spray Bottle

IP SBS732

$6.00

This sprayer adjusts to dispense a fine, medium, or heavy mist. The sprayer is made of polypropylene. The bottle is made of high-density polyethylene.

Holds 8 ounces of liquid.  

T-slotted Urethane Knife Blades

IP ABT836

$8.00

T-slotted blades allow you to quickly exchange blades by pulling forward and down on a blade. To put in a new blade, push it into the lower part of the knife, push it up into the locking pins, and then push it backward. This motion locks the blade securely in place until you need to replace it again.

For use in the Equalizer® Samurai. 

Package of 10

4" Standard Blade

IP EEB793

$8.00

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 8" and 12" sizes.

Invented by: Ray Asbery

Made of Spring Steel

Extra Long Utility Knife Blades • 10

IP ULB582

$8.00

You know the problem: you like to use a long knife but the blade never sticks out of the tool far enough to cut through the thick urethane. Standard utility knife blades measure only 2-3/8" long. The maximum cutting area you can get is approximately 1". Equalizer® extra-long utility knife blades measure a big 3-3/4" long and give you an exposed cutting area of, at least, 2-1/4". They are designed so there is more length between the two notches. For this reason, these blades will fit most standard utility knives as well as all long knives that use the standard utility knife blade.

Package of ten. 

Made in the USA.

Wirestarter™ • 4"

IP WS782

$8.00

Wirestarter™ is a hollow stainless steel tube with grip used to channel cord and wire through urethane. 

To use, push the tube through the urethane, insert the wire through the tube, then pull Wirestarter™ out, leaving the wire in. Be sure to lay the flat side of the aluminum handle against the glass and then use your thumb or fingers to push the tube through the urethane. Also, be sure to concentrate your force directly in line with the tube. Failure to follow these directions may result in the tube bending.

Wirestarter™ • 8"

IP WS782P

$8.00

Wirestarter™ is a hollow stainless steel tube with grip used to channel cord and wire through urethane. 

To use, push the tube through the urethane, insert the wire through the tube, then pull Wirestarter™ out, leaving the wire in. Be sure to lay the flat side of the aluminum handle against the glass and then use your thumb or fingers to push the tube through the urethane. Also, be sure to concentrate your force directly in line with the tube. Failure to follow these directions may result in the tube bending.

8" Standard Blade

IP EEB795

$9.00

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 8" and 12" sizes.

Invented by: Ray Asbery

Made of Spring Steel

4" Serrated Blade

IP ESB1304

$9.00

Invented by: Ray Asbery

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 8" and 12" sizes.

Made in of spring steel in the USA.