Auto Glass Tools - Equalizer®

12" Standard Blade

IP EEB797

$10.00

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 4" and 8" sizes.

Invented by: Ray Asbery

Made of Spring Steel 

12" Standard Blades • 5

IP EEB797PKG

$43.00

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 4" &  8" sizes.

Invented by: Ray Asbery

Made of Spring Steel in the USA.

12-Volt Battery

IP ETSB5

$50.00

Replacement 12-Volt battery for BTB E-Tool providing up to 30 minutes of non-stop operation, depending on the application.

Weighs only 3.5 lbs.

Battery life is 300-600 charges.

Does not include a bag.

14" PipeKnife®

IP GC1144

$21.00

This tool has been around the industry for years and is still one of the most used long knives. The PipeKnife™ is 14" long and has a 6-1/2" flattened blade shaft with rounded corners. The PipeKnife™ is made of cast aluminum but has a steel nut cast into the back side to receive the screw and prevent stripping of the threads. Take out the rear plug and you can put a pipe in the handle to extend its length.

The PipeKnife™ can use all standard utility knife blades including our ULB582 and DD1086 Extra-Long Utility Knife Blades.

Blades not included.

Made in the USA.

14" PipeKnife® With Neoprene Cover

IP SI1412

$23.00

This tool has been around the industry for years and is still one of the most used long knives. The PipeKnife™ is 14" long and has a 6-1/2" flattened blade shaft with rounded corners. The PipeKnife™ is made of cast aluminum but has a steel nut cast into the back side to receive the screw and prevent stripping of the threads. Take out the rear plug and you can put a pipe in the handle to extend its length. The PipeKnife™ can use all standard utility knife blades including our ULB582 and DD1086 Extra-Long Utility Knife Blades.

Blades not included.

Made in the USA.

18" PipeKnife® With Neoprene Cover

IP SK1414

$35.00

One of the useful things PipeKnife™ XL has incorporated is a slot cast into the end of the handle that stores extra blades.

PipeKnife™ XL is made of cast aluminum, is 18" long and has a flattened blade shaft that is 8-1/2" with rounded corners. It has a steel nut cast into the aluminum for the blade clamp screw. PipeKnife™ XL  use all standard utility knife blades including our ULB582 and DD1086 Extra-Long Utility Knife Blades.

Blades not included.

Made in the USA.

18" PipeKnife® XL

IP NN1335

$33.00

One of the nice things the PipeKnife™ XL has is a slot cast into the end of the handle that lets you store extra blades. The PipeKnife™ XL is made of cast aluminum, is 18" long and has a flattened blade shaft that is 8-1/2" with rounded corners. It has a steel nut cast into the aluminum for the blade clamp screw. The PipeKnife™ XL can use all standard utility knife blades including our ULB582 and DD1086 Extra-Long Utility Knife Blades. Blades not included.

Made in the USA.

18" Telescopic Cutting Knife

IP ALK230

$31.00

This knife adjusts from its shortest length of 18” long and extends up to 24” in length. Features extra blade storage area under the blade holder. Comes with one standard utility knife blade.

3/4" Z Coined Cold Knife Blade • 5

IP Z4

$17.00

These innovative blades will remain flexible and retain their sharpness much longer than the average cold knife blade. The grinding of the blade is at a greater angle than other cold knife blades. This makes the resistance less when pulling the cold knife to cut the urethane. The end result is a cold knife blade that has the ability to resist breaking, last longer and keep a sharp edge. Equalizer produces two types of cold knife blades. Both the standard and the coined blades use the same proprietary hardening process.

The Coined Z Blade... The cutting surface of a coined cold knife blade has the cutting surface of the blade made thinner, only about 35 thousandths of an inch thick. A normal cold knife blade is 62 thousandths thick. Many technicians routinely grind cold knife blades thinner so they will cut easier. Sometimes this grinding will overheat a blade and damage the hardening. Coined Z blades are thinned before they are hardened so there is no need to grind them thinner.

Should I buy coined or not coined blades?

If you use a cold knife blade right out of the box and never grind it thinner, then use the standard thickness Z1, Z2, Z3, or Z7. If you like to take a new blade and grind it thinner before you use it, then you should purchase the "pre-thinned" Z4, Z5, Z6 or Z8.

Made in the USA.

3/4" Z Cold Knife Blades • 5

IP Z1

$12.00

These innovative blades will remain flexible and retain their sharpness much longer than the average cold knife blade. The grinding of the blade is at a greater angle than other cold knife blades. This makes the resistance less when pulling the cold knife to cut the urethane. The end result is a cold knife blade that has the ability to resist breaking, last longer and keep a sharp edge. Equalizer produces two types of cold knife blades. Both the standard and the coined blades use the same proprietary hardening process.

The Coined Z Blade... The cutting surface of a coined cold knife blade has the cutting surface of the blade made thinner, only about 35 thousandths of an inch thick. A normal cold knife blade is 62 thousandths thick. Many technicians routinely grind cold knife blades thinner so they will cut easier. Sometimes this grinding will overheat a blade and damage the hardening. Coined Z blades are thinned before they are hardened so there is no need to grind them thinner.

Should I buy coined or not coined blades?

If you use a cold knife blade right out of the box and never grind it thinner, then use the standard thickness Z1, Z2, Z3, or Z7. If you like to take a new blade and grind it thinner before you use it, then you should purchase the "pre-thinned" Z4, Z5, Z6 or Z8.

Made in the USA.

3/8" Z Cold Knife Blades • 5

IP Z9

$13.00

3/8" Equalizer® Z Cold Knife Blades (Pkg. 5)

These innovative blades will remain flexible and retain their sharpness much longer than the average cold knife blade. The grinding of the blade is at a greater angle than other cold knife blades. This makes the resistance less when pulling the cold knife to cut the urethane. The end result is a cold knife blade that has the ability to resist breaking, last longer and keep a sharp edge. Equalizer produces two types of cold knife blades. Both the standard and the coined blades use the same proprietary hardening process.

The Coined Z Blade... The cutting surface of a coined cold knife blade has the cutting surface of the blade made thinner, only about 35 thousandths of an inch thick. A normal cold knife blade is 62 thousandths thick. Many technicians routinely grind cold knife blades thinner so they will cut easier. Sometimes this grinding will overheat a blade and damage the hardening. Coined Z blades are thinned before they are hardened so there is no need to grind them thinner.

Should I buy coined or not coined blades?

If you use a cold knife blade right out of the box and never grind it thinner, then use the standard thickness Z1, Z2, Z3, or Z7. If you like to take a new blade and grind it thinner before you use it, then you should purchase the "pre-thinned" Z4, Z5, Z6 or Z8.

Made in the USA

4" Serrated Blade

IP ESB1304

$9.00

Invented by: Ray Asbery

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 8" and 12" sizes.

Made in of spring steel in the USA.

4" Serrated Blades • 5

IP ESB1304PKG

$38.00

Invented by: Ray Asbery

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 8" and 12" sizes.

Package of five.

Made in of spring steel in the USA.

4" Sheath

IP EES804

$24.00

The sheath is the unique idea that makes the Equalizer® line of tools work. The sheath is a protective sleeve that surrounds the blade so the blade will not damage the dash or garnish moldings. These three sheaths will fit any of the Equalizer® line of tools except the tools that utilize HydroBlade™ technology.

Made in the USA.

Invented by: Ray Asbery.

Sheaths are also available in 8" and 12" sizes.

4" Standard Blade

IP EEB793

$8.00

All Equalizer® Blades have the correct Rockwell hardness so they will not buckle inside the sheath. The serrated style is sharpened with a unique double-serration method. Each serration is also serrated which gives a smoother and faster-cutting action. These blades will fit any Equalizer® tool, including the Excalibur® which is still available as well as the discontinued Equalizer® GT, Equalizer® Magnum, Magnum XP, Thor™, Equalizer® 12V, Equalizer® Freedom and LiveWire™. They will not fit the Equalizer® Express® auto glass cut-out knives. Use of any blades other than Equalizer® Blades will damage your tool and void your warranty.

Also available in 8" and 12" sizes.

Invented by: Ray Asbery

Made of Spring Steel