Auto Glass Tools - Equalizer®

Ford F-150 (2004-2008) Pickup Clip Remover

IP FTF399

$16.00

Used to remove clips from the retainer on the body of the vehicle. Also works on Nissan Maxima and many others. Made of high-quality hardened steel.  

Removal: 

Slip the thin front end of the tool between the tabs on the clip and the receiver clip. Pry up slightly, and all the locking tabs are held apart while the molding is lifted out.

Invented by: Mike Kendall 

ClipFork™ Clip Remover

IP MCR633

$36.00

The Equalizer^® ClipFork^™ will remove step clips used on most Honda vehicles.

Honda & Acura Clip Removal Tool

IP JLT656

$21.00

Designed to work on a wide range of Honda and Acura vehicles with smaller or narrower openings than some of the older clips. 

• Honda Accord (2003 and up)

• Honda Civic (2001 and up)

• Honda Odyssey

• Honda Acura RL, TL and TSX (2005 and up)

A-Pillar Release Tool

IP FCT686

$16.00

This tool works on Ford Flex and Mini Cooper as well as many others with the arrow tipped style clips.

Made in the USA.

Recessed Cowling Clip Removal Tool

IP CTD607

$12.00

Recessed Cowling Clip Removal Tool easily fits down into recessed areas.  To use, slide the tip under the head of the cowling clip, then pull up on the center locking pin and remove the clip.

Cowling Clip Removal Tool

IP CCR819

$36.00

This tool has a small, sharp auger that bites into the plastic head of an expansion-type cowling clip and makes pulling the plastic head possible. The clip will then collapses and can easily be removed. 

Clip Removal Tool

IP TPE657

$12.00

Our Clip Removal Tool has a V-groove with sharpened tips so it will slip under the head of the clip. Simply push the handle down and pry the clips out. Works on many cowling and many drip gaskets.

Door Panel & Cowling Clip Removal Tools

IP CRT250

$53.00

Equalizer™ door panel & cowling clip removal tools are made with different size openings that grab and hold clips. Made in different lengths and configurations so you can place them behind the door panel into hard to reach recessed clips.

Made of the highest quality, heat-treated stainless steel. 

Set of five tools.

Double-End Moulding Release Tool

IP DEC381

$7.00

This tool has a small rubber spacer at each end to keep the tool above the glass by about 1/32" preventing the tool from scratching the glass. It also holds the tool end above the glass, lessening the chance of the tip catching the edge of the glass and breaking it. Made of steel.

Christmas Tree Moulding Remover

IP RFM683

$16.00

This tool is thin enough to fit under moldings and wide enough so as not to tear them. The long curve allows for leverage to pry against the glass. The wide shank is coated with soft plastic so it absorbs shock and is less likely to break the glass.

Made in the USA.

Moulding Release Tool

IP MR747

$9.00

Slide the tool left or right under the molding until it hooks a retaining clip. Rock the tool with a twist of the wrist to pull the clip out slightly. This releases the molding from the clip. Heat treated high carbon steel.

Double-Direction Moulding Release Tool

IP IW1214

$7.00

Our Double-Direction Moulding Release Tool is made of hardened steel and has been an industry standard for over 50 years.

Toyota, Honda, Infiniti, Acura & Subaru Clip Remover

IP TCR370

$18.00

Works on Toyota, Honda, Infiniti, Lexus, Acura & Subaru.

To remove these clips, slide the clip remover under the molding then push the tool down between the clip part that is attached to the body and the part that is attached to the molding. Next pry the clip up lightly. This disengages the teeth and releases the clip.

To remove Toyota clips, push the double-pronged end of the tool toward the pinchweld and push the tool handle downward toward the glass, prying the clip up.

Made in the USA.

PryBaby™

IP GBM446

$24.00

This set contains 5 specially shaped sticks for prying, smoothing, spreading and removing. Each tool is made of a tough yet flexible polycarbonate material.

Tool #1: This widest PryBaby™ is 2-3/8” with one straight chisel and one 90° curve. This tool is great for removing snap-off moldings and cowlings.

Tool #2: Shaped like an installation stick on one end and on the other a tool to remove door panel clips.

Tool #3: One end has an 85° angle and the other end has a 30° angle. Can be used to remove door panels

Tool #4: Very similar to an installation stick but with a 45° angle on one end and a 90° angle on the other.  Very useful for prying small items.

Tool #5: Has a 110° bend that is good for removing door panels when you cannot get into the front part near the door jam area. It has a large oval at one end, so you can press the tool against the door jam without wrapping your hand around it which is important when limited space in that area is available.

PryDaddy™

IP PDT443

$60.00

This set contains 12 tools of which 11 are specially shaped sticks and one is a hammer.  They are for all of your prying, smoothing, spreading, removing, tapping, and pushing needs.

Each tool is made of a tough yet flexible, polycarbonate material.

Comes in a handy roll-up tool pouch.